Appliance Repair Help
Quality Factory Appliance Parts
Quality Appliance Service
Common Parts
::  Washer Parts   
::  Dryer Parts   
::  Refrigerator Parts
::  Dishwasher Parts
::  Range/Oven Parts  
::  Icemakers & Icemaker Parts  
Monthly Special  
:: GE  Refrigerator Water Filter  2 Pack     
:: MWF2  2 Pack     
Save 13%
Lane Appliance
Quality Parts  
::  Factory Authorized Parts  
::  Same Day Shipping  
::  Most Parts In Stock  
::  Call Toll Free Today!  
::  1-866-745-2554  
::  Same Day Service  
::  90 Day Labor Guarantee  
::  Free Online Repair Help
::  Over 15 years Experience  
::  Professional & Courteous
Thank you for the way you handled my
microwave repair. I can see you are in
business to build relationships and can
look past the short term. I will not hesitate
to refer you to my friends and family.

Trudy M.
Thank you again for your helpfulness. We
certainly recommend the quality and
helpfulness of your work and the integrity
of the way you do it, every chance we get.

Katie O.
Monthly Tip  
Cleaning out the lint build up inside your
dryer is very important.  The accumulation
of lint can catch fire and spread to your
home. The lint will also act as insulation
on your motor and cause premature
failure.  All dryers and there vents should
be cleaned at least once a year. Doing
this will keep your family safe and your
dryer operating.
Please remember that working on appliances can be dangerous.  Appliances have many
mechanical and electrical parts that can cause serious injury and death.  If you aren't familiar
with these types of applications then please call a qualified appliance technician. Lane
Appliance LLC and this site accept no responsibility for injuries to person or damage to
To convert your Roper dryer to use LP gas, start by unplugging the
electric,and shutting off the gas to the dryer

Start by raising the top of the dryer.  Raising the top can be accomplished
by removing the 2 screws under the lint filter.  After the screws are removed
grasp the top on the sides with both hands and pull forward and up.  The
top will then hinge to the back.

Verify that the front panel is all one panel or two panels.  If it is two panels
then you will have to start by removing the bottom panel.  This can be
accomplished by pulling on the sides of both panels until it flips down or
inserting a putty knife into the top of the lower panel on both sides to
release the retaining clips.  If your dryer is the type with the top retaining
clips then be careful not to pull on the sides as this will damage the top
retaining clips.

Now that the lower panel is removed you will have to remove the 2 screws at
the top of the upper panel and loosen the 2 screws at the bottom of the
upper panel.  Remove the wire harness or terminal leads to free top panel
from dryer.  Be careful to properly mark the wires so you install them
correctly when reassembling.

If your model is just one front panel then you just remove the 2 top screws,
remove wires or harness, and lift panel up and away from dryer.

Remove belt from motor and idler pulley and remove drum.

You now have access to the burner assembly.

Remove burner tube by removing the screws securing it to the base.  On
older models you may have to remove the entire burner assembly.

Remove the burner orifice by using a 3/8 nut driver.  Install new orifice per
installation instructions that come with part.  Numbers will be marked on
orifice telling which is LP and which is butane orifice.

Remove cap and install blocking pin.

Install conversion labels supplied with kit.

Check for gas leaks and reassemble dryer.
    Roper Dryer LP Gas Conversion
Did this site save you an expensive service call? Please show thanks and......
La Porte
Michigan City
South Bend
Toll Free